A Good Week's Work

After all this time, I guess it's time to write SOMETHING here. It's not the rollout of anything huge, and no photos of the layout yet, but it's been a productive week at last on the Slate Creek.

The hardshell is nearly framed in the "Canyon" area, from the tunnel portal to the large rock cut. Today, I located a source of Hydrocal in Greensboro, and obtained a 100 pound bag, and enough aluminum screen to do the rest of the "crunchy" parts of the mountains in the as-yet-unnamed Canyon area. I have a roll of vinyl screen that will form the base of the somewhat gentler and more uniform hills from the cut through the woods to Midway, and around the corner to where the High Bridge will be (though approaching the bridge, we'll probably be back to metal screen again.) This week's objective was to have plaster cloth up on the canyon section, and I almost made it! At this point, I expect to at least have most of the screen up and maybe some plaster cloth; I may be able to make a larger dent in it next week. If anyone knows an army of tiny people who can reach the far corners of the benchwork, not step on the track in the process, and apply plaster, have them call me! Until then, this is primarily a solo act, and subject to interruption.

** Note: All place titles on the SCRY are just working titles -- once this is finished, I may give them real "Timetable" names. For now, I've got to call it SOMETHING so I'm trying to be consistent in how I refer to these places so as not to confuse anyone.

In other news, I've been working for several years with some good friends on a project to build some passenger equipment with a more modern feel than most commercially available cars or kits. The project was covered over on the Durango Dan site a week or so ago (see link to the left for One twenty point me) and can be seen in depth on Bruce Chandler's website, www.thejoat.com where you can read about the history of the project, and of parlor cars in general. I'll cover mine in detail after it arrives and becomes a project on my own bench -- for now, my car was the test assembly of the kits at Rio Grande Models UK (also see link at left...) and even in its unfinished form is just exciting! Here's a sneak peek...



(That's not the final color...) I have to commend my new friend David Gormley for his fantastic work, and flexibility on this project. When he asked if I'd MIND him assembling mine as a fit-test, I was all too ready to agree, and got him to paint it too ... I'll be doing the detail work, windows, underbody details, and interior once the car arrives here from the UK; Stan Cedarleaf is already putting the decals together for me. One major part of the work will involve scratchbuilding a railing for the observation platform, which should prove interesting. I'm hoping to be able to get most of the other 1:20.3 detail parts commercially (though I already have all of the underbody details.) I'll post updates here as the project progresses.

There's been some discussion lately about the Bachmann Forney. I've got one, and it went from the box to a couple of laps around the track to make sure everything worked, to the workbench. It now looks like this:



As you can see, this is going to be a "roots-up" project, and will entail lowering the cylinders, lowering the body of the locomotive, dealing with the horizontal and vertical seams in the lower part of the smokebox, reconstructing the cab detail, re-engineering the power and control system, and then changing around some of the details to give a family resemblance to another 2-4-4T that's near and dear to my heart in the 1:1 world. I will, of course, post photos and progress here as it happens.

And, there are a zillion other things to do. SCRY #10, a 45 ton diesel, is currently in the shop and will receive the first QSI system on the railroad, followed by Shay #5. There's an enginehouse being built by Randy at PCGRS in California (also in links, left) which will probably come to fruition late in the year, and other motive power and rolling stock projects on the horizon as well.

But first... I need to have a decent "stage" on which these models can perform, so the focus is the layout itself. Hopefully there'll be photographic proof of some progress in that department in the next week or so.

PROGRESS at last!

For the first time in a long time there's some news on the layout itself. The wiring for the new lights is up, and the frames to hold the scenery are installed from the north tunnel portal, past midway, and nearly all the way to the bridge! (of course, you have to think a little fourth-dimensionally to understand where these places are...)

The turntable has a pit, finally, and is visible in the yard. It needs some cosmetic help, and the table may need some reinforcement around it... but it's in, and turns!

There will be photos of all of this very soon, hopefully with some screen work completed too.

An Un-Update

It seems like forever since I've written anything here. Hopefully, that'll change soon, but for now, suffice it to say there's a lot in the works. There's an enginehouse in the design stage, Slate Creek #10 will soon undergo a ground-up rewiring and power / sound system change, I'm working out the final details of the turntable mounting (note that it NEEDS to be in place before the enginehouse arrives,) and oh, yes, the 2-6-6-2 is still awaiting some engineering rework as well.

Then, also, with any luck, we'll have new lights in the basement, so visitors can actually SEE the railroad....

Lots of new and interesting projects on the horizon! Now if I can just get some done enough to take photos, this will be a much more interesting blog to follow.


This photo is from a few years ago, when Gaetan Charette and Nicole came by, and we hit all of the local railroad hot spots... Tweetsie, Doe River Gorge, Spencer ... of course, Cass is something of a stretch to be considered "local," but that's not the point! Gaetan, as well as Bruce Chandler, Doug Matheson, and yours trule also make up a group of folks with a very special 1:20.3 project several years in the making that may turn up here very soon as well!

In any case, stay tuned!

Davenport Rollout

Those of you who saw the photo contest results on Durango Dan's One Twenty Point Me site have seen the first public appearance of Slate Creek Railway #2, the 10 Ton Davenport we've been talking about here since November. I particularly liked the engine that won second place, as I've been considering building something similar for some time now, but I was both pleased and surprised to discover I'd placed in the contest as well.

It's been quite a ride, as you can see in all of the previous posts, from delivery, to teardown, to sandwiching all that gear under the hood, to trying to get everything to function, this little engine has turned into a BIG project. But, even with the external detail changes being somewhat small, the difference is noteworthy, I think:

Before

After

While I still have some more weathering to do, and an antenna issue to work on, this is pretty much what the locomotive will look like from now on. For such a small locomotive, the hours it took to change everything were more than I ever would have guessed... here's a list of "projects" that went into this tiny unit:

a.) Removed factory electronics, and installed RCS radio control, Phoenix P5 sound, P5T interface, and 12 Ni-CD batteries under the hood, the radio under the rear frame, the speaker under the front frame, and the charge jack in the rear wall of the cab.

b.) Removed the Bachmann supplied seat, raised the control stand, and reworked its controls. Added a gear shift lever, clutch, and a new "fold down" style seat in the cab, as well as a pull and valve for the air horns. Also built and added a "sand box" on the fireman's side to match up with the sand fill cover made to cover up the charging jack in the back wall of the cab.

c.) Added the sand fill cover, air horns, and bell, and bell rope. Added the headlight in the rear wall of the cab, and wiring. Also removed the factory stack, and built a replacement one, and replaced the front headlight with a smaller one that looked more the right size for a loco this size. (The one that comes on it is the same as the electric headlight on the 2-8-0!) And, I rebuilt the front end of the locomotive, covering the radiator with HO scale aluminum siding so that the radiator fins would all be horizontal, and removed the handrail supports from the radiator. I made a new grill from brass angle and rod, and added bolts, and a screen to finish it up (the screen was actually some kind of brass decking in HO scale, I think, but it was available in sheets from the LHS!) Oh, and I'm particularly proud of the smokestack; after drawing out what I wanted to do with the front end several times, I was having trouble finding something that "looked right." I looked at toys and truck models, and nothing looked quite right... then I looked at the pen I was drawing with, and realized, if I cut it down, and pulled out the rubber grip....



d.) Finally a set of Slate Creek decals, and some weather treatment to take off the "shine" ... though I'm planning to do more in the weather department in the future.

I'm very pleased with how it came out, particularly since it's my first total conversion/bash/detail project. It will be interesting to see what's next!

I'll sign off with a couple of other photos...

We're Still Here!

It's been awhile!

Somewhere between the holidays and everything else that was going on since my last post, things on the railroad and in the shop have fallen seriously behind, but that's all changing rapidly.

Stay tuned for the "finished" posts on the Davenport (really, I mean it!) Just a little more tweaking and testing, and I'll be ready for a "rolling out!"

I've got to. Something BIG is headed for the Slate Creek shops, and it'll take up the whole shop once it arrives ... I have to make room!

Hopefully this will be a bit more exciting place to visit in the coming months!

Almost There

Yes, I know. Christmas is coming too ...

My "To Do" list on the Davenport (post electrical/mechanical) is down from about 25 items to about a dozen:

Build/Install front and rear headlight lenses
Build sandbox covers.
Install horn and bell pull cords.
Clean and reinstall cab on locomotive
Install radio on locomotive, connect antenna.
Install bell on hood and horns on roof.
Connect front, rear headlights.
Build muffler, remove old smokestack, install new muffler on hood.
Install hood.
Modify radiator & Build grill guard, reinstall
Build and install flag holders, or match paint and cover old hood slots.
Add decals, other graphics, and Marcus.
Test.

And, I think I may see what I can find in the large diecast toy section of Tractor Supply to save me building a muffler... some of theirs are quite detailed, and should work nicely in 1:20.3 for a smaller stack.

I had hoped this post would wave the "FINISHED" banner ... but I'm spending my day dealing with a main drain clog (again,) and may therefore end up delayed for a few days!

Matthew (OV)

Vital Signs

As of today, the major electrical work on the Davenport is finished.

This tiny locomotive now sports 12 NiCd batteries, an ELITE throttle by RCS, and a Phoenix P5 sound system, as well as a P5T interface board, and all of the requisite wiring to make them all work, under the tiny hood.

The power switch is under the rear frame of the locomotive, as is the radio receiver. The small speaker will fit in front, between the frames. The charging jack will go in the rear cab wall, and be disguised by a sand box / cab seat on the inside, and either a sand fill or a handbrake on the outside. I'll go more into the cosmetic details next time, when I have photos to show how they're progressing... the big news TODAY is that other than connecting the headlights, the electrical work on this locomotive is FINISHED!

The first trial fitting of the various components was not especially encouraging (and, I'm told led to indigestion in some quarters!) There seemed to be no way to fit everything in ... and more wire than a local telephone exchange!



I found the best way to overcome the "octopus" the project seemed to be swallowed by was to remove all of the extra wires from the Phoenix and P5T ... there are several extra wires pinned into the plugs that aren't needed for what I'm doing here. I also shortened up harnesses where possible, and then connected what was left in neat, organized bundles. With the battery pack modified from its standard 4-4-4 arrangement to a top row of 4, a middle row of 5, and a bottom row of 3 cells, I found I had room for all of the electronics on top (including the Phoenix P5 at the extreme rear of the hood, vertically,) and sufficient clearance for the worm and gears underneath. With the battery secured to the right hand side of the hood, there was a space along the left that accomodated the P5T, and all of the bundled wires, as well as the volume switch. With the "Octopus" gone, everything finally fit in a functional, if crowded, way.



Much better! The programming port can be removed by unplugging it from the board once the board has been programmed ... which I did (though not before taking the photo above, apparently.) All that was left was a full scale test ... and I'm happy to report everything started up and ran like a charm... both sound and motor. The speaker in the above photo is a full size Phoenix speaker, and I used it just for testing -- the actual speaker is much smaller and will fit between the front frames, and ahead of the power block.

Now to finish up, there's still lots of cosmetic work to do, as well as final re-assembly, and cleaning up all the debris and marks that a major surgery like this always leaves ...

But today, it's alive! ALLLIIIIVE!